BRASS LASER CUTTING SETTINGS POWER, SPEED, FOCUS & THICKNESS
WHAT ARE YOU LOOKING FOR?
Search Across Products, Blog Posts, Support Content, And Resources.
Brass fiber laser cutting settings need to match your machine, material grade, sheet thickness, and required edge quality. Power, cutting speed, focus, assist gas, and nozzle configuration work together to maintain penetration, remove molten material, and control the finished edge.
This guide explains the key settings and presents a 1500W brass cutting reference table by thickness. It also covers how to adjust and validate initial parameters, troubleshoot incomplete cuts, dross, and discoloration, and record settings for repeat production.
Quick Answer: Brass laser cutting settings only work as a complete set.
Start from the reference row that matches your measured sheet thickness, then apply the matching power, speed, frequency, focus, nozzle, gas pressure, and cutting height together. Adapt the set to your own machine and brass grade on a representative test part before you treat any setting as a production parameter.
1. Key Settings for Brass Fiber Laser Cutting
Brass cutting quality depends on how effectively the laser melts the material and how consistently the assist gas removes it. Power, speed, focus, gas pressure, and nozzle configuration need to be matched to the sheet thickness and machine.
1.1 Laser Power and Cutting Speed
Laser power supplies energy; cutting speed determines how long that energy acts on each section of the contour.
Always read a power percentage alongside the machine’s rated output. The same percentage on 1500W and 3000W systems represents different nominal power levels.
When reviewing the cut:
- Incomplete penetration: The selected speed may be too high for the available power and cutting conditions.
- Wide kerf or damaged details: Excessive local heat input may require changes to power, speed, or the cutting path.
- Defects around small holes and corners: Check local speed and power control alongside the settings used for longer contours.
The aim is to sustain penetration while controlling edge quality and heat input.
1.2 Nitrogen, Compressed Air, and Oxygen
Assist gas clears molten brass from the kerf and influences edge oxidation.
- Nitrogen: Helps limit oxidation and preserve a brighter metallic edge. Consider it when visible cut edges are important.
- Compressed air: Can reduce purchased-gas costs on compatible systems. Its oxygen content can affect edge appearance, so include any additional finishing in the cost comparison.
- Oxygen: Use a brass-specific process approved for the exact machine configuration. Published oxygen-assisted brass processes include specialized industrial CO₂ applications, whose settings require their own equipment conditions.
Gas changes should be accompanied by a review of pressure, nozzle, focus, and cutting speed.
1.3 Assist Gas Pressure
Gas pressure must support stable molten-metal removal through the selected nozzle and kerf.
- Insufficient pressure or flow: Molten material may remain attached underneath, producing dross or an unstable cut.
- Excessive pressure: Gas consumption rises, and disturbed flow may worsen the edge.
- Unstable supply: Pressure fluctuations can cause cutting quality to change during a job.
Confirm where the specified pressure is measured and check it while gas is flowing. A pressure reading at the supply regulator can differ from the pressure available at the cutting head. Manufacturer parameter documentation may explicitly identify the cutting-head measurement point.
1.4 Focus Position, Nozzle Size, and Cutting Height
These settings control different parts of the cutting process:
- Focus position: Locates the beam’s smallest diameter relative to the sheet surface. It affects energy distribution through the material. Confirm the calibrated zero and positive/negative direction before entering a value.
- Nozzle size: Influences gas delivery into the kerf. Select its type and diameter together with the gas, pressure, and sheet thickness.
- Cutting height: Sets the distance between the nozzle tip and the sheet. It affects gas delivery and clearance above the material.
Before adjusting these values, inspect nozzle condition and centering, confirm focus calibration, and check sheet flatness. Start from a complete parameter set so each adjustment can be evaluated against a known baseline.

Focus position, nozzle size, and cutting height are separate settings. Cutting height is the gap between the nozzle tip and the sheet, and it changes how the assist gas reaches the kerf.
2. Fiber Laser Cutting Parameters for Brass by Thickness
A thickness-based parameter table provides a starting point for selecting power, speed, focus, and nozzle configuration. Use the complete combination of settings for the corresponding machine and material.
2.1 1500W Brass Cutting Parameter Table
The following reference values come from Thunder Laser’s published 1500W metal cutting parameter library. All four entries use compressed air at 15 bar and a cutting height of 0.5 mm.
| Brass Thickness | Power Setting | Cutting Speed | Frequency | Nozzle | Focus Position |
|---|---|---|---|---|---|
| 0.5 mm | 70% | 30 m/min | 5000 Hz | S1.5 | −1.5 mm |
| 1 mm | 100% | 9 m/min | 3000 Hz | S1.5 | −1.8 mm |
| 2 mm | 100% | 4 m/min | 3000 Hz | S2.0 | −3 mm |
| 3 mm | 100% | 1 m/min | 3000 Hz | S2.0 | −5.5 mm |
Parameter notes:
- Power percentages apply to the referenced 1500W system.
- S1.5 and S2.0 designate single-layer nozzles with nominal diameters of 1.5 and 2.0 mm.
- Focus values follow the published machine settings; confirm the calibrated focus reference before applying them.
- The public table identifies the material as brass. Confirm alloy-specific suitability when selecting settings for your stock.

A brass lead frame cut on a fiber laser. Circular holes, narrow slots, and thin connecting ribs show how a complete parameter set performs on small features, not only on the outer contour.
2.2 How Thickness Affects Cutting Speed
The reference settings show a substantial speed reduction as thickness increases:
- 1 mm brass: 9 m/min at 100% power.
- 2 mm brass: 4 m/min at 100% power.
- 3 mm brass: 1 m/min at 100% power.
Focus and nozzle settings also change across these thicknesses. Read each row as a coordinated parameter set.
Quality requirements matter alongside speed. AccuMetal’s current specifications distinguish 2 mm brass cutting through without dross from 3 mm brass cut-through only. Evaluate finishing needs before treating a cut-through setting as a production setting.
2.3 How to Read and Use the Parameter Table
- Match the application: Confirm the laser configuration, brass grade, measured thickness, and surface condition.
- Check units: The table uses m/min. For controllers using mm/s, 1 m/min equals approximately 16.67 mm/s.
- Apply the supporting settings: Include gas pressure, nozzle, focus, cutting height, and the appropriate machine-approved piercing preset.
- Validate the result: Inspect penetration, underside dross, small features, and critical dimensions before saving the settings for production.
For the complete reference records, visit the 1500W metal cutting parameter library.
3. How to Optimize Brass Laser Cutting Parameters
Begin with a complete parameter set matched to your machine and brass thickness. Check equipment condition first, then adjust one relevant setting at a time so you can identify what improves the result.
3.1 How to Adjust Settings for Different Thicknesses
- Thin brass sheet: Focus on controlling heat around corners, holes, and narrow connections. If these features melt or distort while long contours cut correctly, review their local power, speed, and cutting sequence.
- Thicker brass sheet: Prioritize continuous penetration and molten-metal removal. Check focus, nozzle configuration, and gas delivery before adjusting the power–speed combination.
- Detailed contours: Evaluate small features separately from the outer profile. Review piercing locations, lead-ins, and spacing where repeated nearby cuts concentrate heat.
Use the reference settings for each thickness as the baseline. Record any changes alongside their effect on penetration, dross, and dimensions.
3.2 How to Test and Validate Initial Settings
- Check the machine: Inspect the protective window and nozzle according to the manufacturer’s procedure. Confirm nozzle centering, focus calibration, cooling, and gas supply.
- Confirm the material: Verify the brass grade, measured thickness, surface condition, and selected parameter set.
- Run a representative test: Include a straight edge, circle, narrow slot, and features similar to those in the actual part.
- Inspect and adjust: Examine penetration, underside dross, edge appearance, and critical dimensions. Change one relevant parameter and compare the result with the baseline.
- Validate the actual job: Cut several production parts and confirm that quality remains acceptable across the planned layout.
Keep the test geometry and inspection method consistent when comparing adjustments.
3.3 How to Record Repeatable Production Parameters
Save an approved process record containing:
- Machine and material: Machine configuration, brass grade, supplier or batch, thickness, and surface condition.
- Cutting settings: Power, speed, frequency, focus, assist gas, pressure, nozzle, cutting height, and piercing preset.
- Quality evidence: Front, back, and edge photographs; measured dimensions; dross condition; and required finishing.
- Production details: File version, layout, processing time, test date, and operator.
Name the record so operators can identify the material, thickness, gas, and machine configuration quickly. Recheck the process when material, optics, nozzle configuration, or supply conditions change.
4. Common Brass Laser Cutting Problems and Solutions
Use the defect’s location and appearance to guide troubleshooting. Problems affecting the entire contour require different checks from defects concentrated around holes, corners, or piercing points.
4.1 Incomplete Cutting
Typical signs: Uncut sections, attached parts, or penetration that stops partway through a contour.
- Check first: Confirm the material thickness and complete parameter set. Inspect nozzle condition, gas delivery during cutting, and focus calibration.
- Review power and speed: If the setup is correct, compare the selected speed and power with the manufacturer’s reference for that thickness.
- Inspect local features: When long contours cut through but small holes fail, review their piercing settings, lead-ins, and local cutting conditions.
Record whether the failure starts at piercing, occurs throughout the path, or appears only in particular features.
4.2 Dross and Burrs
Typical signs: Solidified material attached to the underside or rough projections along the edge.
- Check gas delivery: Confirm adequate flowing pressure and inspect the nozzle for damage, contamination, or misalignment.
- Review focus and speed: An unsuitable combination can affect how molten material leaves the kerf. Compare adjustments against the same test geometry.
- Assess the required finish: Define whether the part must be acceptable as cut or may receive deburring. Brass production guidance distinguishes these acceptance conditions.
Include deburring time when evaluating whether a setting is suitable for production.
4.3 Discolored Edges
Typical signs: Darkening or a visible color change along the cut edge.
- Identify the gas: Compressed-air cutting can produce a different edge appearance from nitrogen cutting. Nitrogen generally helps preserve a brighter edge.
- Check the supply: Confirm that gas quality and delivery meet the process specification, including filtration and drying for compressed air.
- Review heat input: Compare discoloration around slow-moving details with that along longer contours.
- Apply the finish requirement: For visible edges, evaluate an approved nitrogen process or the planned polishing operation.
Judge discoloration alongside dross, dimensions, and the final surface requirement.
4.4 Inconsistent Cutting Quality
Typical signs: A job starts cleanly and deteriorates, or similar parts show different results across the sheet.
- Quality changes over time: Check protective-window condition, nozzle buildup, cooling, and gas-supply stability.
- Quality changes by sheet position: Check flatness, cutting-height control, and nozzle clearance.
- Quality changes around dense patterns: Review cutting sequence and part spacing for localized heat accumulation.
Record when and where the change begins. This helps separate an equipment or supply issue from a parameter or layout issue.
5. Do Different Brass Grades Need Different Settings?
Brass grades differ in copper–zinc composition, which affects thermal conductivity and melting temperature. For example, Copper Development Association data show that C23000 brass, with approximately 85% copper, has a thermal conductivity of about 159 W/(m·K) and a liquidus temperature of 1027°C, compared with 121 W/(m·K) and 954°C for C26000, with approximately 70% copper.

Copper content drives both thermal conductivity and liquidus temperature. Higher-copper grades such as C23000 carry heat away faster and melt at a higher temperature than C26000.
These differences suggest that higher-copper grades such as C23000 may need more heat input to maintain penetration. When transferring settings from C26000, a lower cutting speed or higher power may therefore be needed. Use this as an adjustment direction, then confirm the settings through trial cuts; copper content alone does not determine a fixed correction.
Conclusion
Reliable brass laser cutting starts with a complete parameter set matched to the machine, sheet thickness, and material grade. Adjust power and speed alongside focus, gas delivery, and nozzle configuration, then validate penetration, edge quality, and small features on the actual part. Save the approved settings with sample photos and inspection results for repeat production.
Need Help Matching a Cutting Setup to Your Brass Parts?
Share your material grade, thickness, drawings, and required finish with Thunder Laser. Our team can assess suitable machine configurations and arrange sample testing.
Discuss Your Brass Cutting RequirementsTalk To Our Experts Now!
Please leave your contact information so that we can serve you better.
BRASS LASER CUTTING SETTINGS
POWER, SPEED, FOCUS & THICKNESS FAQ
The reference table above lists 9 m/min at 100% power for 1 mm brass and 4 m/min at 100% power for 2 mm brass, both using compressed air at 15 bar. Use the corresponding nozzle, focus, and cutting-height settings from the same row, then validate the combination on your machine and material.
No. The reference table uses 70% power for 0.5 mm brass and 100% for thicker sheets. Select power together with speed and thickness. Small holes, corners, and narrow features may also need different local settings to control heat.
No. Lower speed can help when insufficient heat input causes incomplete penetration, but excessive slowing can increase heat buildup and damage fine details. Check focus, nozzle condition, and gas delivery before assuming that speed is the cause.
Start with the manufacturer’s reference for your machine configuration and sheet thickness. Confirm the calibrated zero point and the controller’s positive and negative direction. Evaluate changes through trial cuts, checking penetration, underside dross, and edge quality. Focus position and nozzle cutting height are separate settings.
Rated power alone does not define the cutting conditions. Optics, focus calibration, nozzle configuration, gas delivery, and machine condition can differ. Brass grade and surface condition also affect results. Transfer the complete parameter set as a starting point, then verify it on the receiving machine.
NEED HELP FINDING THE RIGHT SOLUTION?
Talk to our team for machine recommendations, application advice, and support based on your needs.
























