Complete Your Laser Workshop with Thunder Air Fume Extractor. Learn More
Application

WHAT ARE YOU LOOKING FOR?

Search Across Products, Blog Posts, Support Content, And Resources.

Search

BRASS LASER CUTTING THICKNESS CHART POWER, THICKNESS & SPEED AT A GLANCE

2026-11-17

A fiber laser can cut brass from thin sheet to thick plate, but the achievable thickness depends on more than laser power alone. The laser source, optics, assist gas, material grade and required edge quality all affect the result.

This guide covers brass cutting thicknesses from 1,000W to 30,000W, with reference examples and cutting speeds to explain what different power levels can achieve.

Quick Answer

Brass cutting examples include approximately 2 mm at 1,000W, 6–8 mm at 3,000W, 10–15 mm at 6,000W, and 19–20 mm on selected higher-power configurations.

These figures describe different cutting setups. They include maximum-thickness ratings and reference cutting conditions, so they should be read together with the quality and speed information below.

Brass Laser Cutting Thickness Chart by Power

Laser PowerBrass Thickness ExamplesMeaning of the Figure
1,000W2 mmMaximum-thickness example
1,500W3–4 mmCut-through and maximum-thickness examples; finishing requirements vary
2,000W5 mmMaximum-thickness example
3,000W6–8 mmMaximum-thickness examples for different configurations
4,000WApproximately 8 mmMaximum-thickness examples
6,000W10–15 mmMaximum-thickness examples; a 12 mm nitrogen-cutting condition is also available
8,000W16 mmReference nitrogen-cutting condition
9,000W12.7 mm and 18 mmDifferent maximum-thickness ratings
10,000WApproximately 15 mmMaximum-thickness example
12,000W12.7–15 mm maximum ratings; 16 mm under a reference cutting conditionDifferent configurations and process conditions
15,000WApproximately 19 mm maximum rating; 16 mm under a reference cutting conditionDifferent configurations and process conditions
20,000WApproximately 19 mm maximum rating; 16 mm under a reference cutting conditionDifferent configurations and process conditions
24,000W12.7 mmMaximum rating for one configuration
30,000WApproximately 19–20 mmMaximum-rating and reference cutting examples

These are reference examples, not a continuous power-to-thickness curve. A higher-power configuration may share the same thickness rating as a lower-power one while providing different cutting speeds.

A maximum-thickness rating also does not guarantee a dross-free edge, a polished finish or the required quality around every small feature.

Brass thickness examples published for laser power levels from 1,000W to 30,000W

The same figures by power level: the bars are not a curve, and 24,000W is rated lower than 15,000W.

1. How Thick Can a 1000W–2000W Fiber Laser Cut Brass?

1.1 1000W Brass Cutting Thickness

A 1,000W fiber laser can cut approximately 2 mm brass in a suitable configuration. This provides a reference for thin-sheet brass work.

At the upper end of a machine’s capacity, inspect the complete contour. A straight cut alone does not establish whether small holes, narrow slots and corners meet the same quality requirement.

1.2 1500W Brass Cutting Thickness

For selected 1,500W configurations, brass cutting examples extend to approximately 3–4 mm. The acceptable finished thickness can be lower.

For example, one cutting setup distinguishes:

  • 2 mm brass: Cut through without dross.
  • 3 mm brass: Cut-through only.

This distinction matters when the part must be used directly after cutting. A successfully separated part may still require deburring or edge cleaning.

Thickness also affects processing speed. One 1,500W compressed-air process uses the following reference conditions:

Brass ThicknessCutting SpeedPower Setting
1 mm9 m/min100%
2 mm4 m/min100%
3 mm1 m/min100%

These conditions use 15 bar compressed air, with the corresponding nozzle, focus and cutting-height settings. The speeds belong to that complete setup and require validation before use on another system.

Cutting speed for 1, 2 and 3 mm brass with a 1,500W compressed-air process

1,500W compressed-air process: 9 m/min at 1 mm falls to 1 m/min at 3 mm.

1.3 2000W Brass Cutting Thickness

A 2,000W configuration can have a maximum brass thickness of approximately 5 mm.

For parts near that thickness, assess continuous penetration, the underside of the cut and the amount of finishing required. The thickness figure identifies a capability example; the actual part establishes whether that capability is useful for the job.

2. How Thick Can a 3000W–6000W Fiber Laser Cut Brass?

2.1 3000W Brass Cutting Thickness

Selected 3,000W fiber laser configurations have maximum brass thicknesses around 6–8 mm.

This power level therefore includes capability beyond thin sheet. However, a 6 mm part and an 8 mm part may place different demands on piercing, cutting speed and melt removal.

When evaluating the upper thickness, inspect:

  • Complete separation around the whole part.
  • Dross along the bottom edge.
  • Small holes and internal contours.
  • The time required to complete and finish the part.

Laser-cut brass and stainless steel gaskets, flanges and profiled parts of different thickness

Brass and stainless gaskets, flanges and profiled parts: the same thickness figure covers very different contours.

2.2 4000W Brass Cutting Thickness

For selected 4,000W configurations, maximum brass thickness is approximately 8 mm.

The improvement over a lower-power machine may involve speed at a shared thickness rather than a large increase in maximum thickness. Compare equivalent material and part requirements when assessing that difference, and weigh the faster process against the cost of the higher-power machine.

2.3 6000W Brass Cutting Thickness

For 6,000W configurations, maximum brass thickness examples range from approximately 10 to 15 mm.

There are also reference nitrogen-cutting conditions for 12 mm brass at 0.6–1.0 m/min.

This illustrates the difference between a thickness limit and an operating condition. “12 mm at 0.6–1.0 m/min” gives more information about a potential process than a thickness figure alone, although it still does not describe the complete part cycle or final edge acceptance.

3. How Thick Can an 8000W–12000W Fiber Laser Cut Brass?

This range includes thicker-brass capability, with differences between the available configurations.

Laser PowerBrass Cutting Capability Examples
8,000WA 16 mm nitrogen-cutting condition at 0.3–0.5 m/min
9,000WMaximum-thickness ratings of 12.7 mm and 18 mm on different configurations
10,000WA maximum-thickness rating of approximately 15 mm
12,000WMaximum ratings of 12.7 mm and approximately 15 mm, plus a 16 mm nitrogen-cutting condition at 0.8–1.0 m/min

3.1 What Changes at the Same Thickness?

For 16 mm brass, the two reference nitrogen-cutting conditions show:

  • 8,000W: 0.3–0.5 m/min.
  • 12,000W: 0.8–1.0 m/min.

The higher power provides a faster reference process at the same thickness.

To understand the effect on a finished part, account for its total contour length, piercing operations, corners and small features. The increase in straight-line cutting speed does not automatically produce the same percentage reduction in complete job time.

Reference cutting speeds for 16 mm brass at 8,000W, 12,000W, 15,000W and 20,000W

At a fixed 16 mm, rising power buys speed: 0.3–0.5 m/min at 8,000W against 1.5–2.4 m/min at 20,000W.

3.2 Why Does 9000W Have More Than One Thickness Figure?

The figures describe different cutting systems and process conditions. A wattage rating alone does not establish one maximum thickness for every system using that power.

The table should therefore be used to identify capability examples rather than calculate thickness by interpolation. A value for 9,000W cannot establish a guaranteed result for 10,000W or 12,000W.

4. How Thick Can a 15000W–30000W Fiber Laser Cut Brass?

4.1 High-Power Brass Cutting Thickness

Selected 15,000W, 20,000W and 30,000W configurations have maximum brass ratings of approximately 19 mm.

Separate nitrogen-cutting conditions include:

Laser PowerBrass ThicknessReference Cutting Speed
15,000W16 mm1.3–1.8 m/min
20,000W16 mm1.5–2.4 m/min
30,000W20 mm0.6–1.5 m/min

These examples show that thick-brass processing extends well beyond the 1–3 mm range. They also show why the associated cutting speed is useful when evaluating a thick-plate application.

4.2 Does More Power Always Mean More Thickness?

No. Higher power can improve speed at an already-supported thickness while the maximum thickness remains unchanged.

For example, a particular 24,000W configuration has a brass rating of 12.7 mm, while some lower-power configurations have higher ratings. This does not mean additional power reduces cutting ability; the figures describe different complete systems.

A machine’s maximum brass thickness is therefore a specification of the complete cutting configuration rather than a simple conversion from watts to millimetres. The process parameters behind a thickness rating — power, speed, focus, gas and nozzle — are set together, not one at a time.

4.3 What Does a 20 mm Cutting Example Tell You?

A 30,000W reference condition for 20 mm brass establishes a specific thick-plate processing example. It does not establish 30,000W as the universal minimum power for that thickness.

For an actual 20 mm part, evaluate:

  • Whether piercing completes reliably.
  • Whether penetration remains continuous.
  • The cut face and bottom-edge condition.
  • Internal features and dimensional requirements.
  • Complete machining and finishing time.

These checks determine whether the result satisfies the intended application.

Conclusion

Fiber laser brass cutting capabilities extend from thin sheet into thick plate. Reference examples include approximately 2 mm at 1,000W, 6–8 mm at 3,000W, 10–15 mm at 6,000W, and 19–20 mm on selected higher-power systems.

Read thickness together with the cutting configuration, edge quality and speed. For a specific job, provide the brass grade, thickness, drawing and required finish so the appropriate cutting process can be evaluated.

Discuss Your Brass Cutting Requirements

Share your brass grade, thickness, drawing and required finish with our application team.

Talk to an Application Engineer

Or review the Thunder AccuMetal Series for fiber laser metal cutting configurations.

Contents
Brass Laser Cutting Thickness Chart by Power
1. How Thick Can a 1000W–2000W Fiber Laser Cut Brass?
2. How Thick Can a 3000W–6000W Fiber Laser Cut Brass?
3. How Thick Can an 8000W–12000W Fiber Laser Cut Brass?
4. How Thick Can a 15000W–30000W Fiber Laser Cut Brass?
Conclusion

Talk To Our Experts Now!

Please leave your contact information so that we can serve you better.

Name*
Email*
Country*
Your Message

BRASS LASER CUTTING THICKNESS

POWER, THICKNESS & SPEED FAQ

Q1: How thick can a 1500W fiber laser cut brass?

Selected configurations have cut-through or maximum-thickness examples around 3–4 mm. A lower thickness may be appropriate when a clean edge is required. One setup distinguishes 2 mm without dross from 3 mm cut-through only.

Q2: Can a 3000W fiber laser cut 6 mm brass?

Yes, suitable 3,000W configurations can cut 6 mm brass. Confirm the complete process and inspect the edge, underside and internal features at the required thickness.

Q3: Can a 6000W fiber laser cut 15 mm brass?

Some configurations have a 15 mm maximum brass rating, while others have lower ratings. Confirm the capability for the exact cutting setup, including the required finish and processing time.

Q4: What laser power can cut 20 mm brass?

A 30,000W nitrogen-cutting example processes 20 mm brass at 0.6–1.5 m/min. This is a reference process, not a universal minimum-power requirement.

Q5: Does doubling laser power double brass cutting thickness?

No. Cutting thickness does not follow a fixed linear relationship with wattage. Additional power may increase speed at the same thickness while the maximum-thickness rating remains unchanged.

NEED HELP FINDING THE RIGHT SOLUTION?

Talk to our team for machine recommendations, application advice, and support based on your needs.

We use cookies to understand how our audience uses our site.
THUNDER LASER websites use cookies to deliver and improve the website experience, See our cookie policy for further details on how we use cookies and how to change your cookie settings Cookie policy.
Accept
Reject
close